Plumbing Basics: An Essential for When Installing a Bathtub
Plumbing Basics: An Essential for When Installing a Bathtub
Blog Article
Were you searching for resources concerning How to Install a Bathtub?
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard project. If the old bathtub is easily obtainable, the task can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also position the new bath tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub and set in the new one. See to it you have certified on your own for the task and fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a new bath tub in your shower room if you have actually currently purchased a new bathtub and don't need to transform the setup of your previous water pipes.
Your tools as well as material list must consist of the following:
Preparing for the Installment
To start with, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of both wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bath tub till the level reviews level.
To install taps, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the bath tub and likewise examine the overflow outlet as well as the typical outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait until the bathtub has been utilized at the very least when as this will certainly resolve it right into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type needs to be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to crack an inflexible seal, triggering the water to permeate the wall surface between the bath as well as the tiling, causing problems with moisture and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub? Try leaving feedback further down. We will be pleased to know your insights about this post. Hoping to see you back again before long. Liked our blog posting? Please share it. Help another person locate it. We love reading our article about Installing A Bathtub.
Information Here Report this page